Shenzhen Jun Tai Feng Novel Material co., ltd



Silicone Potting Sealant

Shenzhen Jun Tai Feng novel material co., ltd

Tel: 0755-29694891 0755-29694892

Fax: 0755-29694893



Address: Shenzhen Bright new District, public-ming potato field PO Community Emerging Industrial Zone A, the first second floor 201

Silicone Potting Sealant
Abstract: JTF-105 Room-temperature curable silicone potting sealant

High-strength, highly transparent siliconePotting Glue。 Apply to soft and hard light drop gum.


JTF-105 Room-temperature curable silicone potting sealantMainly for the existing packaging materials (epoxy resins, PU glue, PU modified epoxy, etc.), such as yellowing, heat dissipation and other fatal defects developed for the various sections led soft light strips as well as piranha, the Great Wall lamps and other LED decorative lamp special potting, this series of packaging glue with high transparency, high heat dissipation, The light in the water does not have the characteristics of fog and never yellowing.

I. Functions and Features:

JTF-105 Potting SealantMainly used for LED decorative lamp potting its main functions are as follows:

1, it has excellent waterproof, can protect the lighting is not water immersion, and long-term water in the light does not fog;

2, with excellent heat dissipation, can ensure that the chip in the use of the process will not be due to excessive temperature and affect the service life;

3, with excellent transmittance and refractive index, can minimize the light decay of the light source;

4, with super Anti-ultraviolet ability, to ensure that the lighting in its service life will never turn yellow;

5, with excellent weather performance, to ensure that the lighting in a wide range of temperature ( -40~220℃) and underwater, such as the normal use of special circumstances, so that the use of lighting area almost unlimited;

6, this series of products are cured at room temperature, the main curing mechanism is with the air moisture reaction and curing, so the temperature is not sensitive, so that its curing conditions require simpler, easier to operate.

Second, technical specifications:


Three: How to use:

1, with glue, this series of glue are two-part liquid, the use of two parts in accordance with 4:1 of the proportion of mixing, and mixing equipment to fully stir (be sure to ensure that two parts mixed evenly), note: Must ensure that the mixing rod and the container cleaning (not with the rest of the glue contact);

2, vacuum, after the glue will be placed in the bubble-blowing device for bubble treatment, because the silica gel molecular tension is small, so in the vacuum when the bubble is very easy to accumulate, you can see a lot of bubbles very fierce platoon out. So in order to avoid the waste of glue, in the vacuum, as many times as possible in the discharge valve place gas;

3, after the elimination of bubbles, you can transfer glue into professional potting equipment for drip irrigation;

4, after the drop gum, placed 4 hours or so, when the surface does not stick to the hand (after the full table dry) can be packaged;

Note: It is recommended that the customer should pay attention to the whole process of stirring time about 1-2min, bubble time of about 3-5min, as far as possible to ensure that mixing and bubble time not more than 10 minutes to avoid subsequent potting time too little, even inefficient operation (this time for experience, customers can according to their own dispensing volume, And the operation of the process of their own grasp).

Four, security:

1, silicone potting adhesive for pure silicone products, does not contain any harmful substances, is environmentally friendly products, even if the human body direct contact will not have any adverse reactions;

2, this series of products is not flammable product, will not produce volatile substances, no risk of explosion;

3, this series of products in the curing process will not produce any harmful substances, the environment and no harm to the human body.

Five, Attention matters:

1, this glue can not be mixed with other glue;

2, two parts of the mix should be as far as possible to ensure a uniform mixing;

3, mix well after the glue, if the conditions permit should be as far as possible to discharge bubble treatment;

4, has been equipped with good glue must be in the operating time to avoid unnecessary waste;

5, in the potting Groove products should be as far as possible to fill the full point, after curing the appearance will be more beautiful, as the use of the surface of the glue is recommended to customers in the first time after the drop, after the gel and then reconfigure the glue water droplets second time, after curing the appearance will be better

6, so the series of glue in response to water, not used up the glue must be sealed to save the storage conditions at room temperature in a cool place to save the best;

7, this product should try to avoid long-term contact with the washing board water, days that water and so on and solvents and strong acid and alkali;

8, this model glue hardness in 20 degrees, when the use of the lamp packaging glue hardness in 50 degrees below, will appear glue sticky too close and dead lamp phenomenon, so this model glue is not suitable for hardness too low lamp above;

9, because this product is chemical products, your specific production process is not the Division I can control, so before using the sample, suitable, please rest assured use.

June Tai Fung Shenzhen New Materials Co., Ltd. was founded in 2009. is a collection research and development, production and sales of High-tech private enterprises. Company is located in Shenzhen Bright New District, the public office, CI Tin po Emerging industrial zone. Adjacent to Hong Kong and Macao, superior geographical location and traffic environment, to provide customers with convenient service! Its products have screen potting glue and so on.

Previous: No Information

下一条: Silicone ventilation Adhesive